microcontroller

Build a Programmer for the 68HC705C8 MicroController

Introduction This programmer is used for programming the Motorola 68HC705C8 (or C8A). The 68HC705C8 has the following attributes; 8K bytes of internal EPROM 304 bytes of internal RAM 24 user-definable input/output ports 7 Input only ports Serial Control Interface (SCI) Serial Peripheral Interface (SPI) 16 bit capture/compare timer system Watch Dog timer This micro-controller is […]

Build a Programmer for the 68HC705C8 MicroController Read More »

internetworking with microchip microcontroller pic18f+enc28j60

Description The ENC28J60 is Microchip’s first incursion into the ethernet controller arena, this new device includes all MAC & PHY IEEE 802.3 10BaseT functions, 8KB of dual access RAM packet buffer and a SPI serial interface, all in a convenient 28-pin package (SPDIP, SOIC, SSOP and QFN packages available). It takes just few components to

internetworking with microchip microcontroller pic18f+enc28j60 Read More »

PIC microcontroller ATA library

This project started life a long time ago, with the intention to build an iPod clone, back when personal MP3 players were an expensive luxury and long before you could buy them from China on ebay for less than a light bulb. The plan for the MP3 player was to use a PIC microcontroller connected

PIC microcontroller ATA library Read More »

Hello World Project With PIC Microcontroller – Part II

Hello Friends, Welcome back. In the last tutorial we started working with MPLab and HI-TECH C Compiler and written our first C program to blink LED. After compiling the program we got the HEX file. Now, in this tutorial we will see how to transfer(burn) the hex file to our Microcontroller chip and then power it

Hello World Project With PIC Microcontroller – Part II Read More »

Microcontroller Schematic Design Software

Microcontroller Schematic Design Software Microcontroller Schematic Design Software is a electronics design software(EDS) that is used for the prototyping and simulation of embedded system that contains microcontrollers. The usual steps taken for designing microcontroller based embedded system using microcontroller circuit design software are- 1. Create a schematic of the design 2. Create Program for the

Microcontroller Schematic Design Software Read More »

automatic power factor controller using microcontroller

The 230 V, 50 Hz is step downed using voltage transformer and current transformer is used to extract the waveforms of current. The output of the voltage transformer is proportional to the voltage across the load and output of current transformer is proportional to the currentG‚throughG‚the load. These waveforms are fed to Voltage Comparators const

automatic power factor controller using microcontroller Read More »

First Time Programming a Microcontroller

First Time Programming a Microcontroller In my previous post we have carried out the construction of the base Circuit board for our USB demo Interface Board.So lets begin with out next part for little but more info about the pic18f USB on PCB. (If wish then you can also review my pic18f4550 tutorial for beginner)

First Time Programming a Microcontroller Read More »

Stepper Motor Driver using PIC18F4550 Microcontroller

Stepper Motor Tutorial In this tutorial we are going to drive a Single unipolar stepper motor using PIC18F4550 Microcontroller in various different stepping modes. The source code and Project files are free to download at the end of this page. Stepper motor due its excellent features is very famous in between hobbyist for various robotic

Stepper Motor Driver using PIC18F4550 Microcontroller Read More »

Microcontrollers with USB interface are common, but…

Microcontrollers with USB interface are common nowadays. Manufacturers provide source codes for USB device classes like CDC, HID, Mass storage and DFU. . Even in this case, programming USB communications may not be a trivial task. If it is only required to replace RS232 serial interface to USB, is worth considering using of FTDI TF-X

Microcontrollers with USB interface are common, but… Read More »

IR(infrared) Remote Control Relay Board with PIC 12F675 Microcontroller

Introduction This little project will demonstrate how you can use your old NEC IR protocol based TV,DVD or VCR remote control to control you home appliances like fan bulb or virtually anything. Consumer IR protocols There are a number of consumer Infrared protocols out there and they have been used for every single purpose possible i guess, like

IR(infrared) Remote Control Relay Board with PIC 12F675 Microcontroller Read More »

	GPS Projects
	Internet and LAN Projects
	Interfacing(USB) Projects
	Metering & Instrument Projects
	Sensor – Detector Projects
	Motor Based Projects
	Phone Based Projects
	Robotics and Automation Projects
	Camera – Imaging and Video Projects
	Game and Entertainment Projects
	Home Automation Based Projects
	Memory and Storage Projects
	RFID Based Projects
	Security and Safety Projects
	Sound and Audio Projects
	Temperature Measurement Based Projects
	DIY Projects
	Medical and Health based Projects
	Battery Based Projects
	PWM (Pulse-width modulation) Projects
	Radio Based Projects
	Others Project
	Calculator Based Projects
	Car - Auto Projects
	LCD Based Projects
	LED Based Projects
	Clock and Timer Projects
	CNC-Machines Projects
	Development Board Projects
	RTOS Projects