Summary of Low Cost 1 Wire Lcd for 8 Pin Micro Controllers [romanblack Shift1 System ]
Shift1 System is a low-cost solution that expands digital output pins using only one PIC microcontroller pin. It utilizes a serial-in parallel-out shift register (74HC595) and an RC network to distinguish between 0 and 1 bits based on pulse duration, eliminating the need for separate data and clock lines. The project includes a micro development board, MOSFETs, resistors, capacitors, and components for LCD contrast adjustment.Parts used in the Shift1 System:
- 74hc595
- 1.5 k resistor
- 33 k resistor
- 0.1uf polyster capacitor
- 2.2nf non capacitor
- 220 ohm resistor
- 2n7000 mosfet
- 5K preset
- Button switch
- Pic12f675 microcontroller

Step 1: How It Works - the Simple System
Normally, serial-in parallel-out shift register ICs can be set up for 2 pin operation;
DAT - data, is the next bit to be shifted in
CLK - clock pulse, on / edge the next bit is shifted in
This can be "cheated" to just use one pin and timed-length pulse. An RC network is used to provide a time delay for the DAT line to change. Very short pulses mean that a 1 bit is shifted in. With a long enough pulse the DAT voltage drops low enough so that a 0 bit is shifted in when the CLK line goes / again.
Step 2: Shift1 LATCHED System for Driving LCDs
reference link : http://www.romanblack.com/shift1.htm
Step 3: Circuit Diagram

1, 74hc595 - 1
2, 1.5 k resistor -1
3, 33 k resistor - 1
4, 0.1uf polyster capacitor -1
5, 2.2nf non capacitor - 2
6, 220 ohm resistor -1
7, 2n7000 mosfet -1
8 ,5K preset - 1 ,for lcd contrast adjust
9, button switch - lcd back light ON/OFF [optional ]10, pic12f675
Step 4: Vero Board Assembling

Step 5: Test Board - Pic12F675 Micro Development Board [3.0 Cm X 2.5 Cm Size]

pic12F675 micro development board
Step 6: Finished Circuit Board

Step 7: Working Video
special thanks to roman black.
Source: Low Cost 1 Wire Lcd for 8 Pin Micro Controllers [romanblack Shift1 System ]
Quick Solutions to Questions related to Shift1 System:
- How does the system work with only one pin?
An RC network provides a time delay so short pulses shift in a 1 bit while long pulses drop the voltage low enough to shift in a 0 bit. - What IC is used for serial-to-parallel conversion?
The project uses a 74hc595 shift register IC. - Which microcontroller is recommended for this project?
The Pic12f675 microcontroller is used as the driver. - Can this system drive an LCD display?
Yes, the article describes a latched version specifically designed for driving LCDs. - What component adjusts the LCD contrast?
A 5K preset is used for LCD contrast adjustment. - Is there an option to control the LCD backlight?
Yes, a button switch can be added for optional LCD backlight ON/OFF control. - Does the design require two wires for operation?
No, it is designed to use just one pin by cheating the standard two-pin setup.
Related projects
Leveraging Blockout Banners for Effective Electronics and Tech Product Displays
Blockout banners have become a popular and effective tool for displaying electronics and tech products in various settings, from trade shows and...
LCD & Display Projects · PIC18F4520Interfacing PIC18F4520 microcontroller with an HD44780 LCD
Introduction Being able to display data from a microcontroller visually has many advantages. It allows for menus, status indicators, and instructions to...
LCD & Display ProjectsVideo Project Development in the Midst of an Impromptu Online Semester
Receiving robot parts in the mail was an unexpected conclusion to the Winter 2020 semester for students. However, when faced with a...
LCD & Display Projects · PIC16F628AFrequency Counter by PIC16F628
In this project we are building a basic and low cost frequency counter circuit . It can measure from 16Hz to 100Hz...
LCD & Display ProjectsWHAT IS A PIC MICROCONTROLLER? WHAT CAN IT DO?
PIC microcontrollers ( Programmable Interface Controllers), are electronic circuits that can be programmed to carry out a vast range of tasks. They...
LCD & Display Projects · PIC16F877ASerial Data Received from PC and Displayed on 16×2 Using USART of Pic16f877 Microcontroller
Here is a simple tutorial on how to receive serial data from PC(Personal Computer) Hyperterminal and display it on 16x2 lcd using...