INTRODUCTION This application note describes the technique used to program and verify a X32 or B series microcontroller (MCU), and how to construct the programmer board (PGMR) used in conjunction with this application note. All that is required to program an MCU is the PGMR and a +5 volt and a V PP dc power […]
M68HC705X32 PROGRAMMER BOARD Read More »
Catalog What is the Reason Why Some Plugs Have Three Prongs While Others Do Not? How Does the Third Prong on a Plug Work? The Difference Between a Two-pronged Plug and a Three-pronged Plug Could the Ground Prong Be Cut or Fitted with an Adapter Safely? The Process of Changing a Two-prong Outlet to a
What is the Three Prong Plug? Read More »
Overview This adapter allows you to interface with your car’s OBD-II bus. It provides you a USB interface using the ELM327 command set and supports all major OBD-II standards: SAE J1850 PWM SAE J1850 VPW ISO 9141-2 ISO 14230-4 ISO 15765-4 CAN Hardware The adapter kit schematic is shown here. It is built around NXP LPC1517
OBD-II ELM327 compatible AllPro adapter using PIC18F2455 Read More »
This device reads a DMX-512 signal and grabs a variable amount of channel data values and sends them at 57200 or 19200 baud to an external device, such as a 24 Channel High Current LED Controller, when a new data packet is requested. This allows any microcontroller(PIC, Arduino, ATMel, ect.) with TTL serial communication to accept
DMX-512 to Serial Adapter Read More »
Communicating with a micro-controller at runtime, is a very usefulfacility. It can be used for debugging, or to send commands etc. One of the easiest available protocol to communicate is UART. It requires a pin for transmit and a pin for receive, and the GROUND connection. There are many available programs that allow us to
Generic UART for Any Microcontroller Read More »
Microchip PIC microcontroller to program the tar socket Series programlaycı ICSP programmer great convenience, but also do not have these facilities on a shared circuit DIP adapter between 8 …. 40 Pin PIC microcontroller… Electronics Projects, 8-40 Pin DIP Adapter for Microchip PIC Series “pic development board, “ Microchip PIC microcontroller to program the tar socket Series programlaycı ICSP
8-40 PIN DIP ADAPTER FOR MICROCHIP PIC SERIES Read More »
Overview This adapter allows you to interface with your car’s OBD-II bus. It provides you a USB interface using the ELM327 command set and supports all major OBD-II standards: SAE J1850 PWM SAE J1850 VPW ISO 9141-2 ISO 14230-4 ISO 15765-4 CAN Hardware You do not have to be familiar with all the details of
Simple USB to RS232 adapter on pic18f2455 Read More »
Introduction This program is an experimental timed-discharge adapter for a Vericom control panel used with an Orenco Systems AdvanTex® wastewater treatment system (sewage filtration system) marketed by Wastewater Technologies, Inc. Although the Vericom firmware is capable of modification to provide timed-discharge capability by a firmware download via telephone, this adapter was just an experiment to
TIMED DISCHARGE ADAPTER using PIC16F628 Read More »
Adding a Digital Meter and Functions to Analog Geiger Counters The Digital Meter Adapter is a expansion module for adding digital functions to Analog Geiger Counters that have a pulse output. If you’re geiger counter outputs a ttl pulse for every radioactive particle it detects, your Geiger counter will connect to Images SI Inc.’s DMAD
Digital Meter Adapter – DMAD Read More »
Since 2008, PIC Microcontroller has provided students, hobbyists, and engineers with quality PIC projects, tutorials, PDFs, software, tools, and embedded systems resources.
© 2008 – 2026 PIC Microcontroller. All Rights Reserved.
