battery | Battery Guide

Single microcontroller based 12v to 230v inverter with intelligent battery charging

Single microcontroller based 12v to 230v inverter with intelligent battery charging (Made by me) Here I describe the circuit as: *single microcontroller/controller (ATMEGA16/32) *no op-amps, only chips are the micro, opto-couplers and regulator (7805) *low-battery/overload/short-circuit protection *thyristor controlled battery charger, using the MOSFET body diode as the AC-DC rectifier *charger maintains the battery voltage (top) […]

Single microcontroller based 12v to 230v inverter with intelligent battery charging Read More »

Maximize the Energy from Long-Life Batteries

Battery lifetime is a key consideration for the development of the wireless sensor nodes that will populate the Industrial Internet of Things (IIoT). In many applications, the sensor nodes will need to be installed in locations that are difficult to reach let alone service. The sensor nodes need to be autonomous in terms of energy

Maximize the Energy from Long-Life Batteries Read More »

AmpStrike – Battery Powered Bench Power Supply

Linear Voltage Regulator The power supply runs on a linear voltage regulator built on discrete components. The design of the linear regulator was inspired by the user Amspire from the EEVblog forum. The basic idea is that the Q1 pass transistor and U5A op amp act in a classic voltage regulating loop. U5A gets feedback

AmpStrike – Battery Powered Bench Power Supply Read More »

Smart Battery Charger (no soldering!)

Many AA or AAA battery chargers charge batteries in pairs, but plenty of devices use 1 or 3 batteries, meaning that some of your batteries get overcharged and some get undercharged. NiCd and NiMH batteries also benefit from an occasional full discharge, which most normal battery chargers won’t do. If you’re anything like me you’ll

Smart Battery Charger (no soldering!) Read More »

DIY, Microcontroller-Based Battery Monitor for RC Aircraft

I’ve had good cause to be reading and perusing a few old Circuit Cellar articles every day for the past several weeks. We’re preparing the upcoming 25th anniversary issue of Circuit Cellar, and part of the process is reviewing the company’s archives back to the first issue. As I read through Circuit Cellar 143 (2002)

DIY, Microcontroller-Based Battery Monitor for RC Aircraft Read More »

Battery Powered Frequency Meter (0 to 20kHz)

The circuit is a simple digital frequency meter that is made of a frequency-to-voltage converter and an analog-to-digital display converter that can be operated from a single 9-volt battery. The TC7126 ADC generates the voltage required by the TC9400 FVC with internal regulators. The TC7126 is designed to directly drive a 3-1/2 digit, non-multiplexed LCD

Battery Powered Frequency Meter (0 to 20kHz) Read More »

Lithium-Ion Battery Warms Up, Operates In Subzero Temperatures

A new “all-climate” lithium-ion battery can rapidly heat itself to overcome freezing temperatures with little sacrifice in energy storage capacity and power, researchers say. This advance might enable applications for which high-performance batteries are needed in extremely cold temperatures, such as electric cars in cold climates, high-altitude drones, and space exploration. EC Power is now

Lithium-Ion Battery Warms Up, Operates In Subzero Temperatures Read More »

Intelligent 4-Cell Lithium Battery Management with CAN/LIN Interface

This design is a battery management circuit, which involves the use of CAN/LIN interface. The system addresses the matter about managing rechargeable batteries. This design features an 8-output hardware configurable, high side/low switch with 16-bit serial input control using the serial peripheral interface (SPI). Two of the outputs are directly controlled using a microcontroller which

Intelligent 4-Cell Lithium Battery Management with CAN/LIN Interface Read More »

9 Volt Battery Charger

9 Volt batteries extensively used in various electronics measurement equipment. Powering these devices with rechargeable batteries can be a cost effective solution. In this post a simple Lithium-ion 9 Volt Battery Charger design with overcharging protection will be presented. Charger is based on PIC16F876A microcontroller and uses its A/D module to monitor current flow into

9 Volt Battery Charger Read More »

One step closer to the ‘ultimate battery’

Although scientists are still working toward replacing lithium-ion (Li-ion) batteries with lithium-air (Li-air), or lithium-oxygen, batteries, researchers at the University of Cambridge have developed a lab-based demonstrator of such a battery. It is safe to say we still have another decade before we can begin to utilize such powerful batteries as scientists work to make

One step closer to the ‘ultimate battery’ Read More »

	GPS Projects
	Internet and LAN Projects
	Interfacing(USB) Projects
	Metering & Instrument Projects
	Sensor – Detector Projects
	Motor Based Projects
	Phone Based Projects
	Robotics and Automation Projects
	Camera – Imaging and Video Projects
	Game and Entertainment Projects
	Home Automation Based Projects
	Memory and Storage Projects
	RFID Based Projects
	Security and Safety Projects
	Sound and Audio Projects
	Temperature Measurement Based Projects
	DIY Projects
	Medical and Health based Projects
	Battery Based Projects
	PWM (Pulse-width modulation) Projects
	Radio Based Projects
	Others Project
	Calculator Based Projects
	Car - Auto Projects
	LCD Based Projects
	LED Based Projects
	Clock and Timer Projects
	CNC-Machines Projects
	Development Board Projects
	RTOS Projects